EXPERIMENTAL

Autograph 250kN

Maker：SHIMADZU／Model：AG-250KN／Year of Introduction：2018／Measure mechanical strength of a specimen. Maximum load capacity and load cell rated capacity are 250 kN.
Autograph 5kN

Maker：SHIMADZU／Model：AGS-5kNX／Year of Introduction：2017／Measure mechanical strength of a specimen. Maximum load capacity and load cell rated capacity are 5kN.
Ball Mill

Maker：Retsch／Model：MM400 ／Year of Introduction：2022／Grinding of small samples with a maximum capacity of 2×20 ML. The powder and suspension can be mixed and homogenized.
Biolab

Year of Introduction：2018／Controlled environment maintained in sterile conditions for mycelium-based innovations with a vertical HEPA filter. Also, contains incubators and autoclave.
CO2 Chamber

Maker：MARUI＆CO.LTD／Model：MIT-639-3-05／：2021／Exposure specimen by changing the dimensions in an atmosphere with varying temperature, humidity, and CO2 concentration.
Compression Tester 3000KN

Maker：SHIMADZU／Model：CCH-3000kN ／Year of Introduction：1996／Measure mechanical strength tests of high-strength concrete, rock, etc. It has a maximum load capacity of 3000KN.
Cone Calorimeter

Maker：Fire Testing Technology／Model：iConeClassic／Year of Instruction：2023／Measure property against fire of the material being tested under a variety of preset fire conditions.
Crusher

Model：YOSHIDA／Model：1025-HB／Year of Introduction：1996／Grind coarsely crushed samples. The grinding teeth are flat and disc-shaped, and grinding particle size is adjatable.
Crusher

Maker：Retsch／Model：BB50 ／Year of Introduction：2022／Crush the aggregates into powders with sizes smaller than hundreds of ums. Grind samples up to 40mm.
FT-IR

Maker：Bruker／Model：alpha ／Year of Introduction：2021／Obtain the absorbance spectrum of infrared ray, from which identification of substance and structural analysis can be performed.
Gas Chromatography

Maker：NETZSCH Japan／Model：8890 GC System／Year of Instruction：2022／ quantified and identified components of material using a flame ionization detector and mass spectrometer.
Grinding machine High-polishing vine

Maker：MARUI＆CO.LTD／Model：MIC-196-1-30／Year of Introduction：2018／The surface of the test specimen is finely polished, giving it a uniform gloss and smoothness.
Hybrid mill

Maker：YOSHIDA／model：1066／Year of Introduction：2022／Used for aggregates, etc. After finely pulverizing, the attached screen properly separates the crushed and uncrushed sample.
Micro FT-IR

Maker：Shimadzu／Model：AIM-9000／Year of Introduction：2023／Obtain the absorbance spectrum of infrared ray, from which identification of substance and structural analysis can be performed.
Particle Size Analyzer

Maker：Microtrac／Model：MT3000 ／Year of Introduction：2021／Determine the particle size distribution by analyzing the diffraction pattern that appears behind the particles when the laser light hits them.
Planetary Mixer

Maker：THINKY／Model：ARE-500／Year of Introduction：2021／Mix cement evenly without air bubbles, improving strength consistency and the overall finish quality.
Rheometer

Maker：Anton Paar／Model：RheolabQC／Year of Introduction：2023／Measure flow resistance of liquids and slurries for rheological constants with single-point viscosity and flow curve measurements.
Sectioning Machine

Maker：BUEHLER／Model：IsoMet 11-1280／Year of Introduction：2018／This is a small tabletop saw designed for careful cutting of samples. It has simple controls and a micrometer for control.
Telecentric Measurement System

Maker：Keyence／Model：TM-X5065／Year of Instruction：2021／Silhouette of the specimen is acquired as an image. Measurement can be made with an error of ±2.0μm.
TG

Maker：Rigaku／Model：ULTGA／Year of Introduction：2023／Measure water content and CO2 fixation as TG data with Φ10 x 20 cm test specimens of concrete, etc.
TG-DTA

Maker：Rigaku／Model：TG-DTA8122 ／Year of Introduction：2023／ Measure weight of specimen and temperature difference conpared to reference as a function of temperature or time.
Twister vacuum mixter

Maker：Renfert／Model：Twister II ／Year of Introduction：2019／To mix the cement paste (if you need to mix other materials, please clean the cell carefully after using) in a vacuum state.
Vapor Sorption Analyzer

Maker：Anton Paar／Model：VSTAR／Year of Introduction：ー／Measure sorption isotherms using water vapor or gas. Also, evaluate the pore structure and the surface area based on BET theory.
Vibrating Screen

Maker：TOKUJU／Model：TM-70-3S／Year of Introduction：1995／Sieve aggregates and recycle concrete aggregate/powder. It can classify powders into 0.75mm – 5.0mm.
Viscometer

Maker：Toki Sangyo／Model：TVB-15／Year of Introduction：2011／Measuring the viscosity of liquids by measuring the resistance that a rotating spindle encounters in the liquid.
Water Activity Meter

Maker：Meter／Model：AQUALAB 4TE／Year of Introduction：2020／It measures water activity with ±0.01aw accuracy within 5 minutes. Built-in temperature control maintains a stable 25°C
XRD

Maker：Rigaku／Model：Miniflex ／Year of Introduction：2018／X-ray diffractometer, providing data of phase identification. Also measure crystallite size and degree of crystallinity etc.

Research Project　C4S・GI

Autograph 1000kN

Maker：SHIMADZU／Model：UH-F1000KNAXR／Year of Introduction：2023／Measure mechanical strength of a specimen. Maximum load capacity and load cell rated capacity are 1000 kN.
CO2 Chamber

Maker：ESPEC／Model：PR-4J／Year of Introduction：2023／Exposure specimen by changing the dimensions in an atmosphere with varying temperature, humidity, and CO2 concentration.
Dynamic ultra micro hardness tester

Maker：SHIMADZU／Model：DUH-211／Year of Introduction：2018／ Conduct microscale indentation tests using tiny specimens with mechanically polished surface.
Gas Pycnometer

Maker：Anton Paar／Model：Ultrapyc 5000／Year of Introduction：2021／Measure the density of liquids or solids by calculating the volume and mass. This is essential for accurate material analysis.
Micro Cutting Machine

Maker：Meiwafosis／Model：BS-300CP／Year of Introduction：2020／Precisely cut material to the appropriate size. It can be used for not only super-hard/soft-hard composite specimens.
Nitrogen sorption

Maker：Microtrac／Model：Belsorp MINI X／Year of Introduction：2021／Adsorbing Nitrogen can measure the specific surface area, pore distribution and pore capacity of a sample.
NMR

Maker：Oxford Insturments／Model：MQC+／Year of Instruction：2022／Reflect the characteristics of water-filled pores by measuring the magnetic signals of hydrogen atoms inside a specimen.
Polishing Machine

Maker：PRESI／Model：250SPC／Year of Instruction：2023／Robust, powerful, reliable polishing machine equipped with a Ø200 to 250mm platen/6 pistons/individual and central pressure.
Raman mapping

Maker：nanophoton／Model：Raman walk ／Year of Introduction：2022／Obtain Raman spectrum with visible laser, from which identification of substance and structural analysis can be carried out.
SEM-EDS

Maker：Oxford／Model：TM4000plus／Year of Introduction：2021／Obtain compositional analysis of test material powder using energy-dispersive X-ray spectroscopy.
Single-sided 1H NMR

Maker：MAGRITEK／Model：PM25／Year of Introduction：2023／ Examine distribution of water inside and size of pores. The relaxation time is measured from the free water and pore condition.
Testing Machine 5kN

Maker：SHIMADZU／Model：EZ-SX／Year of Introduction：2023／Measure mechanical strength of a specimen. Maximum load capacity and load cell rated capacity are 500N.
TG-DSC

Maker：Netzsch／Model：STA449F5／Year of Introduction：2021／Measure amount of heat in phase transition of materials based on weight and temperature compared with reference.
TG-DTA

Maker：Netzsch／Model：STA2500 Regulus ／Year of Introduction：2023／Measure amount of heat in phase transition of materials based on weight and temperature compared with reference.
Total Carbon Analyser

Maker：Elementar／Model：soli TOC cube／Year of Instruction：2022／Quantify individual TOC, TIC, and elemental carbon content accurately by using stepwise heating,
Vapor Sorption Analyzer

Maker：Microtrac／Model：BelMAX X／Year of Instruction：2023／Measure sorption isotherms using water vapor or gas. Also, evaluate the pore structure and the surface area based on BET theory.
X-ray CT

Maker：SHIMADZU／Model：Inspexio 100CT／Year of Instruction：2021／Used for high-magnification 3D imaging of materials like concrete and cement paste with observation of internal 3D structures.
XRD

Maker：Panalytical／Model：Empyrean ／Year of Introduction：2021／X-ray diffractometer, providing data of phase identification. Also measure crystallite size and degree of crystallinity etc.
XRD

Maker：Panalytical／Model：Aeris ／Year of Introduction：2024／Examine crystal structure of specimen by diffraction of X-rays. The wavelengths is 0.1 to 10 nm and intensity depends on scattering direction.
XRF

Maker：Panalytical／Model：Epsilon／Year of Introduction：2023／Conduct qualitative and quantitative elemental analysis of materials in various forms including powder, solid, liquid, etc.